LIFT VÀ QUATOUR

PRODUCTION PROCESS MODEL PE 010.

1. LIFT AND QUATOUR:

1.1. Process:

Horn of crude (1) sanding, cleaning horns (2) blowing glue line 2 in (3) Abrasive Adhesive lined 2 sides (4) affixed decal, thaodecal excessive cleaning xang92 (5). Surface blowing color surface color is not blowing Blowing on a color (6) Brush glue on a ball (12) Grinding was a color (7) Grinding was a drag ball (13) Blow color was 2 (8) Blow bong on tape 2 (16) Abrasive tape ball two times (17) Remove the decal, gas cleaning (9). bubble blowing three times (19) Drag on a bubble blowing (10) packing. (23) Grinder was a drag ball (11) check (22) Bubble blowing glue two times (14) Polishing (21) Abrasive tape ball two times (15) Abrasive Fiber (20) Glue bubble blowing three times (18)

1.2.Thuyet intelligence process:

(1): Horn of crude:

(2): sanding, cleaning horns:

a. tasks and objectives: Create smooth level before blowing the horn sheet lining glue 2 sides, cleaning dust no sticking horns.

b.materials: Rough Green Paper 240, paper 400 blue shark, t-shirts. c.practice methods: Using Rough green paper is 400 rub on surface horns, the horns have broken the level of the smooth evenly.

(3): blowing glue lined two aspects:

a.tasks and objectives: Make no gun range roughness.

b.materials: PU lining, gas Sunday.

c.tasks and objectives.: Phase PU lining, fuel is sprayed on the surface of Sun products, spraying the second side.

(4): abrasive tape lined two aspects:

a.tasks and objectives: Create Rough for the next level. Create plane for the product.

b.materials: Rough Paper 600, paper 800 Rough.

c.tasks and objectives: First Rough dung paper 600, rub product to all of nhan.Dung ABRASIVES 800 rub again to grinding flat products and reduce the depth of the scratches.

(5): paste the decal, remove excess decal, gas cleaning 92:

a.tasks and objectives: Preparing for the distribution of color, avoid the blows mau.Mau will cling to the inside patterns, the products were for pham.chuan downstream. b.materials: decal paper, petrol 92, Kapok.

c.tasks and objectives: Use paper decal affixed horizontal patterns, use the arrow next to the sharp pointed knife cut decal sheet by rounded grooves around the flower van.Sau remove the decal remainder unnecessary outside pattern, then use the bong wool soaked in petrol over 92 cleaning products, cleaning glue left after removing the decal mercy.

(6): color distribution was 1:

a.tasks and objectives: Creating Color products required by customers. b.materials: Son expo, gasoline Sunday.

c.tasks and objectives: paint thinner selected with the use of petrol nhat.Sau pistolet are blowing on the surface of the product.

(7): grinding on a color:

a.tasks and objectives: How flat surface product, prepare for the next. b.materials: Rough Old Paper 1000.

c.tasks and objectives: Using the old paper 1000 Rough surface grinding all products, meet the requirements of the product is.

(8): color distribution was 2 :

a.tasks and objectives: cover the fault of the product when mai.Loi here often broken color.

b.materials: Son expo, gasoline Sunday.

c.tasks and objectives: paint thinner selected with the use of petrol nhat.Sau pistolet are blowing on the surface of the product.

(9): remove the decal, gas cleaning 92:

a.tasks and objectives: Remove decal preparation for the next. b. materials: gasoline 92, Kapok, sharp knife.

c.tasks and objectives: Using sharp knife tip pointed slightly from sheet tray decal on the use patterns ra.sau Kapok gasoline soaked wipe over 1992 products, cleaning glue left after removing the decal mercy

(10): bubble blowing on a tape:

a.tasks and objectives: keep the new color layer is sprayed without scratches, on the other hand also makes products more beautiful bong.

b.materials: PU ball, PU hard, gasoline Sunday.

c.tasks and objectives: stir the mixture solution were used pistolet blowing on the surface of products.

(11): abrasive tape was a bong:

a.tasks and objectives: How flat surface product, prepare for the next. b.materials: 1000 Rough Paper, Rough Paper 1200.

c.tasks and objectives: Rough paper for 1000 are slightly abrasive surface products, then use paper to wipe Left Rough 1200 to reduce the scratch paper Rough created in 1000.

(12): bubble blowing on a tape (Like step 10)

a.tasks and objectives:

b.materials:

c.tasks and objectives:

(13): abrasive tape was a bubble (like step 11)

a.muc destination:

b.materials: 1200 emery paper, paper Rough 1500

c.tasks and objectives:

(14): bubble blowing glue two times: (Like step 10)

a.tasks and objectives:

b.materials:

c.tasks and objectives:

(15): abrasive tape ball two times: (Like step 10)

a.tasks and objectives:

b.materials:

c.tasks and objectives:

(16): bubble blowing glue two times: (Like step 11)

a.tasks and objectives:

b.materials:

c.tasks and objectives:

(17): abrasive tape ball two times: (Like step 10)

a.tasks and objectives:

b.materials:

c. :

(18): blowing bubble tape three times: (Like step 11)

a.tasks and objectives:

b.materials: 1200 emery paper, paper Rough 1500

c.cach as:

(19): blowing bubble tape three times: (Like step 10)

a.muc destination:

b.materials:

c.tasks and objectives:

(20): Grinding Optical:

a.tasks and objectives: to create products of flat, making the surface of the ball light products, preparing for the next.

b.materials: Rough Paper 1000, paper 1200 Rough, sandpaper 1500, Rough Paper 2000.

c.tasks and objectives: use paper to wipe all new 1000 Rough surface of products, from paper to wipe Rough 1200 New Left, next to the paper from 1500 the new Rough wipe again, using the new 2000 ABRASIVES ABRASIVES lau lau was cuoi.sau new I finished the old Rough start using paper from Left 1000,1200,1500,2000 wipe until bong beauty products we bring to new polished.

(21): polish:

a.tasks and objectives: make bong beauty products, meet with the requirements of the application hang.

b.materials: cana, Kapok.

c.tasks and objectives: use Kapok soaked cana reviews are on the surface of products so that products are not smooth scratch to meet the requirements of customers.

(22): check: before we pack to go with the need to check if the products meet the requirements for product packaging to bring, we do not meet the requirements to carry repaired.

(23): Packing: Bringing a product to the packaging closed.